Mini Halloween Ghost Amigurumi Crochet Pattern (2)

This tiny Halloween ghost is a playful palm-sized amigurumi with a soft white body, little outstretched arms, and a crooked lilac witch hat finished with a black band and golden-yellow buckle. The construction is intentionally compact, so the finished character stays in the 5-9 cm keychain range while still keeping the friendly proportions of the visual reference.

The pattern is a good project for confident beginners who are comfortable working single crochet in continuous rounds. You will make the head and tapered ghost body as one piece, crochet two simple arms, then build the witch hat from the tip downward. The most important techniques are a magic ring, increases, invisible decreases, tight stuffing, simple embroidery, and neat sewing. Because the hat remains unstuffed, it can be bent into a charming floppy point without adding bulk.

The finished miniature ghost is about 8-9 cm tall including the hat and fits comfortably in one adult hand.

Pattern Overview

Materials

Crochet Abbreviations

Before You Begin

Work the ghost and arms in continuous spiral rounds unless a step says otherwise. Place a stitch marker in the first stitch of every round and move it upward as you work. Count after every shaping round; on a miniature project, one missed increase or decrease can noticeably twist the silhouette.

Keep your tension firm but flexible. The fabric should be dense enough to hide fiberfill while still allowing the safety-eye posts to pass between stitches. Add stuffing in small wisps instead of large clumps, especially around the head-to-body transition and narrow tail. This keeps the ghost smooth rather than lumpy.

For clean color changes on the hat, begin the new color on the final pull-through of the stitch immediately before the color change. The lilac brim is worked into the front loops so it flares outward while the black band remains visible above it.

Complete Crochet Pattern

Step 1 - Main Ghost Body

Use white yarn. The head and body are worked in one continuous piece from the crown down to the pointed ghost tail.

Top-left: form the crossed adjustable loop for the body Round 1 magic ring. Top-right: insert the crochet hook under the ring strand and catch the working yarn. Bottom-left: pull up the loop and secure the start with one chain. Bottom-right: work the first 6 sc into the still-open ring before tightening the tail.

After Round 10, insert the 6 mm safety eyes between Rounds 7 and 8, about 7 stitches apart from center to center. Check the face from the front before pressing the washers fully into place.

Stuff the head firmly enough to stay round, then add smaller pinches through the neck and lower body. Keep the final 1 cm of the tail more lightly stuffed so it can taper naturally.

FO, leaving a short tail. Thread the tail through the front loops of the remaining 4 stitches, pull closed, and hide the yarn end inside the body.

Top-left: the white crown after Round 5 has 30 stitches. Top-right: after Round 10, place the 6 mm eyes between Rounds 7 and 8 while the inside is accessible. Bottom-left: Round 13 widens the narrow neck from 18 to 24 stitches to begin the body. Bottom-right: after Round 21, add stuffing before the tail opening becomes too small.

Step 2 - Arms - Make 2

Use white yarn. The arms are left unstuffed so they remain light and angle naturally from the sides.

Flatten the opening and work 3 sc through both layers to close. FO with a 15 cm sewing tail. Repeat for the second arm.

Step 3 - Crooked Witch Hat

Begin with lilac yarn. The hat is worked from the pointed tip downward and stays unstuffed.

Change to black yarn.

Change back to lilac yarn.

FO and weave in the brim tail. Bend the point gently to one side. If you want a stronger curl, use a short strand of lilac yarn to tack the tip to the side of the cone around Rounds 8-10, then knot the strand inside the open hat.

Use golden-yellow yarn and a tapestry needle to embroider a tiny square buckle centered on the front of the black band. Four short straight stitches are enough at this scale.

Top-left: one white arm in progress around Rounds 3-6. Top-right: the two completed, unstuffed arms with flattened sewing edges. Bottom-left: the lilac hat cone after Round 15, before adding the black band. Bottom-right: the finished hat accessory after Round 19 with the black band, yellow buckle, and gently curved tip.

Step 4 - Assembly

Pin the arms before sewing. Position the closed top edge of each arm across the sides of the body around Rounds 13-15, just below the narrow neck. Angle them slightly upward or outward, then compare both sides from the front and back. Sew through the closed arm edge and the body stitches with small whip stitches. Knot securely and hide each tail inside the ghost.

Set the witch hat on the head with the buckle centered above the face. The inner edge of the brim should sit around the head near Rounds 5-6. Pin the brim at the front, back, and both sides, then sew the inner brim edge to the head with lilac yarn. Keep the stitches shallow so the thread does not distort the face.

With pink floss, embroider a small curved smile centered between Rounds 9 and 10. Two or three short stitches create a soft expression. For optional blush, add one or two tiny horizontal stitches just outside each eye rather than using loose fibers that may rub away.

Top-left: pin both arm edges around body Rounds 13-15 and check symmetry. Top-right: sew an arm securely with a threaded tapestry needle. Bottom-left: position and stitch the inner lilac brim to the head around Rounds 5-6. Bottom-right: embroider the small pink smile after the hat and arms are secure.

Finishing Touches

Roll the stuffed body gently between your palms to smooth any uneven areas. Check that the tail points downward without a hard lump at the tip and that both arms sit at a similar height. If the hat brim lifts, add one extra hidden tack at the back. Trim no yarn tail until you are satisfied with the placement; woven tails are much easier to adjust than cut ones.

For an optional keychain, use a strong needle to anchor a short loop of matching yarn through the head crown and then pass it through the hat crown before the hat is fully secured. Attach a small split ring or lobster clasp to that reinforced loop. Do not suspend the ghost from the hat fabric alone, because repeated pulling can stretch the brim or cone.

Customization Ideas

Troubleshooting

Care Instructions

Frequently Asked Questions

Conclusion

This little Halloween ghost is quick enough for an evening project but detailed enough to feel special, especially once the crooked witch hat and tiny embroidered face are in place. Make one as a seasonal desk charm, add secure hardware for a keychain, or crochet a small set in different hat colors for handmade Halloween gifts.

The completed miniature ghost shown from a different angle, with the smooth tapered tail, matching arms, lilac crooked witch hat, black band, yellow buckle, safety eyes, and pink embroidered smile all in their final positions.